Some glazing on front brake rotors

Discussion in 'Gen 2 Prius Care, Maintenance and Troubleshooting' started by ILuvMyPriusToo, Mar 10, 2015.

  1. ILuvMyPriusToo

    ILuvMyPriusToo Senior Member

    Joined:
    Dec 4, 2014
    780
    518
    0
    Location:
    Outside Philly, PA
    Vehicle:
    2024 Prius Prime
    Model:
    Plug-in Base
    2009 Gen II Prius with 73K miles. I had my state inspections done at the local Toyota dealership and the service manager told me I had "some glazing" on my front disk rotors (not the pads). He said it was *not* a safety issue (he was very clear on that when I asked) but that stopping distances might increase slightly. Recommended remedy was to have the rotors turned (for about $150). Pads are at "7" (mm?; original to the car) and fine, according to the tech. He said the condition might have occurred because of a lot of braking in stop and go traffic that led to the rotors heating up. I don't remember any situation like that recently. He said rotor glaze is permanent and will not wear off; hence the recommendation to machine, but I hate to lose the metal if it isn't necessary. The brakes otherwise seem fine - no wobbles, squeaks or other noticeable issues. Thanks in advance for insights and advice!
     
    #1 ILuvMyPriusToo, Mar 10, 2015
  2. bisco

    bisco cookie crumbler

    Joined:
    May 11, 2005
    113,898
    51,851
    0
    Location:
    boston
    Vehicle:
    2012 Prius Plug-in
    Model:
    Plug-in Base
    i wouldn't do anything. maybe take it to a local shoppe and have them show you the disks.
     
    #2 bisco, Mar 10, 2015
    ILuvMyPriusToo likes this.
  3. 69shovlhed

    69shovlhed Surly tree hugger

    Joined:
    May 13, 2012
    2,170
    751
    0
    Location:
    Delaware
    Vehicle:
    2017 Prius Prime
    Model:
    Prime Premium
    put some valve grinding compound on the rotors and drive it, braking lightly. this will sometimes remove the glazing on normal cars, works great for brake squeaking.
     
    #3 69shovlhed, Mar 10, 2015
    ILuvMyPriusToo likes this.
  4. ChapmanF

    ChapmanF Senior Member

    Joined:
    Mar 30, 2008
    27,493
    18,086
    0
    Location:
    Indiana, USA
    Vehicle:
    2010 Prius
    Model:
    IV
    Ford's official shop manual for my old Bronco II advised against machining in cases of light glazing, and recommended hand sanding with 150 grit sandpaper instead. Seemed to work ok for me.

    I might think twice about grinding compound just because I'm not sure what the liquid is (if it's the kind of compound that comes in a tube like toothpaste). If it's only water I guess it would be ok. Something else, I might not want it on the brake linings.

    -Chap
     
    #4 ChapmanF, Mar 10, 2015
    ILuvMyPriusToo likes this.
  5. xpcman

    xpcman Senior Member

    Joined:
    Jun 11, 2009
    1,302
    295
    0
    Location:
    California - SF Bay area
    Vehicle:
    2008 Prius
    get up to 30 mph on a back road - put it into neutral - apply the brakes hard and come to a complete stop.
    do this 2 or 3 times and you should be OK.

    Remember the "service writer" works on commission !
     
    #5 xpcman, Mar 11, 2015
    ILuvMyPriusToo likes this.
  6. ChapmanF

    ChapmanF Senior Member

    Joined:
    Mar 30, 2008
    27,493
    18,086
    0
    Location:
    Indiana, USA
    Vehicle:
    2010 Prius
    Model:
    IV
    Good technique for brake noise caused by light surface rust after wet weather.

    Only makes glazing shinier.

    -Chap
     
    #6 ChapmanF, Mar 11, 2015
    ILuvMyPriusToo likes this.
  7. exstudent

    exstudent Senior Member

    Joined:
    Jul 11, 2009
    2,214
    905
    0
    Location:
    Torrance, CA
    Vehicle:
    2007 Prius
    Couldn't OP do the same procedure as PriusChat member "Galaxee", did for the rear brake shoes and drums to remove glazing on both items?
    Rear Brake Clean and Adjust | PriusChat
    3. sandpaper the friction surface of the drum with aluminum oxide sandpaper- 80 grit wet or dry is what DH is using here. see how shiny that surface is? that's glazing. the glazing will be removed as well as brake dust. NEVER sand in the direction parts are moving. do not sand around the long surface, sand perpendicular to it. if you sand parallel to the long surface, you can score the surface, which you really do not want to do.​

    Take a medium or heavy grit sandpaper to the front disc rotor and front pads, going perpendicular to the direction of braking. Then clean the rotor and pads again w/ brake cleaner fluid?

    Logically if this works for deglazing the rears, shouldn't it work for the fronts?
     
    #7 exstudent, Mar 11, 2015
    ILuvMyPriusToo likes this.
(You must log in or sign up to post here.)