After Brake Actuator Install

Discussion in 'Gen 2 Prius Care, Maintenance and Troubleshooting' started by Hamza Mughal, Nov 14, 2021.

  1. Hamza Mughal

    Hamza Mughal Junior Member

    Joined:
    Oct 15, 2021
    30
    0
    0
    Location:
    Virginia
    Vehicle:
    2007 Prius
    Model:
    Base
    So I installed the new ABS actuator and there is still that loud beeping noise, is this because of something I have to do in tech stream? I ordered the dongle already for it the mini-Vci but I have no idea what to do besides bleeding brakes.
     
    #1 Hamza Mughal, Nov 14, 2021
  2. SFO

    SFO Senior Member

    Joined:
    Feb 7, 2017
    5,302
    4,244
    0
    Location:
    Northern California
    Vehicle:
    2007 Prius
    Model:
    N/A
    Which OBD2 codes (DTCs) are you retrieving with the OBD2 scanner?
     
    #2 SFO, Nov 14, 2021
  3. ChapmanF

    ChapmanF Senior Member

    Joined:
    Mar 30, 2008
    25,960
    16,943
    0
    Location:
    Indiana, USA
    Vehicle:
    2010 Prius
    Model:
    IV
    The loud beep indicates a failure to build the correct pressure. It might be good to review your installation procedure for any way the actuator could have had air allowed to enter, or isn't completely filled with fluid.
     
    #3 ChapmanF, Nov 14, 2021
  4. Hamza Mughal

    Hamza Mughal Junior Member

    Joined:
    Oct 15, 2021
    30
    0
    0
    Location:
    Virginia
    Vehicle:
    2007 Prius
    Model:
    Base
    Haven’t tried that yet, the car has weak 12v, I am charging it up
     
    #4 Hamza Mughal, Nov 14, 2021
  5. Hamza Mughal

    Hamza Mughal Junior Member

    Joined:
    Oct 15, 2021
    30
    0
    0
    Location:
    Virginia
    Vehicle:
    2007 Prius
    Model:
    Base
    Yeah I think air may have gotten into it, but bleeding the brakes with techstream should fix that right?
     
    #5 Hamza Mughal, Nov 14, 2021
  6. JC91006

    JC91006 Senior Member

    Joined:
    Nov 10, 2013
    16,632
    8,492
    0
    Location:
    Los Angeles, CA
    Vehicle:
    2008 Prius
    Model:
    II
    you must bleed brakes after the install. Can't just install and drive.

    Techstream has the function to do it, but the mini vci cable is not very good. You may lose connection many times as you're trying to bleed the brakes.
     
    #6 JC91006, Nov 15, 2021
  7. koco

    koco Member

    Joined:
    Oct 4, 2021
    113
    38
    0
    Location:
    Las Vegas
    Vehicle:
    2005 Prius
    Model:
    Base
    It will beep after the install. You need to run the bleed function of Techstream and use the "Replaced ABS Actuator" function. It will go through the steps and outline what to do as you go along.

    Check for codes when you are done, you may still have to calibrate the steering angle sensor after the bleed steps are done, and that is separate.
     
    #7 koco, Nov 15, 2021
  8. Hamza Mughal

    Hamza Mughal Junior Member

    Joined:
    Oct 15, 2021
    30
    0
    0
    Location:
    Virginia
    Vehicle:
    2007 Prius
    Model:
    Base
    Thank you very much and also to JC, got tech steam downloaded and waiting for cable now.
     
    #8 Hamza Mughal, Nov 15, 2021
  9. Hamza Mughal

    Hamza Mughal Junior Member

    Joined:
    Oct 15, 2021
    30
    0
    0
    Location:
    Virginia
    Vehicle:
    2007 Prius
    Model:
    Base
    Okay so I keep getting the c1256 and c1253 codes too and also the linear valve offset won’t calibrate and the relays under the hood are making a clicking sound I did the bleed process and got thru it as well
     
    #9 Hamza Mughal, Nov 20, 2021
  10. Hamza Mughal

    Hamza Mughal Junior Member

    Joined:
    Oct 15, 2021
    30
    0
    0
    Location:
    Virginia
    Vehicle:
    2007 Prius
    Model:
    Base
    Also the beeping sound is now gone but I tried doing the steering angle sensor and stuff but it seems to not work
     
    #10 Hamza Mughal, Nov 20, 2021
  11. priustruck

    priustruck New Member

    Joined:
    Feb 6, 2022
    4
    0
    0
    Location:
    DMV
    Vehicle:
    2007 Prius
    Model:
    N/A
    Hello! I am having a similar problem - replaced the brake actuator, put everything back together. Now when I open the door I hear a click from the unit and the terrible warning beep resumes. Also in addition to initial warning lights I now have the ! triangle of death and the red car outline. Was the OP able to get their problem fixed? I am trying to decide whether it is worth it to go buy this techstream or not.
    Thanks so much
     
    #11 priustruck, Feb 6, 2022
  12. SFO

    SFO Senior Member

    Joined:
    Feb 7, 2017
    5,302
    4,244
    0
    Location:
    Northern California
    Vehicle:
    2007 Prius
    Model:
    N/A
    Welcome to PriusChat!!
    Since you have warning lights, do you have any OBD2 codes worth sharing? (you may want to start your own thread for this issue)
    Given the other options, it may be the least expensive approach, and is the same software that a dealer technician would use to diagnose.
     
    #12 SFO, Feb 6, 2022
    priustruck likes this.
(You must log in or sign up to post here.)