do I have a transmission oil pan on my 2008 Prius?

Discussion in 'Gen 2 Prius Care, Maintenance and Troubleshooting' started by Stoner, Dec 20, 2018.

  1. Stoner

    Stoner Junior Member

    Joined:
    Dec 19, 2018
    45
    20
    0
    Location:
    Naples, Florida
    Vehicle:
    2008 Prius
    Model:
    Two
    anybody know if there is a transmission oil pan on a 2008 Prius? I want to do an ATF change in my high mileage (168K). After reading several posts, seems some of the earlier models do have an AT oil pan, but I don't know about mine. I'd like to take it off and clean what I can plus ensure all the old fluid is drained....then start fresh with a new gasket and fluid. I'm placing an order for fluid and would like to include the gasket (if there is one)....not showing up on Amazon.
     
    #1 Stoner, Dec 20, 2018
  2. edthefox5

    edthefox5 Senior Member

    Joined:
    Jul 25, 2007
    10,096
    4,829
    0
    Location:
    Clearwater, Florida
    Vehicle:
    2007 Prius
    Model:
    Two
    Nope no trans pan. Just a fill hex bolt on the front side high on the trans and a big dump bolt on the bottom of the trans that has a magnet on it.

    Hundreds of posts on how to do it.
     
    #2 edthefox5, Dec 20, 2018
  3. bisco

    bisco cookie crumbler

    Joined:
    May 11, 2005
    111,559
    50,803
    0
    Location:
    boston
    Vehicle:
    2012 Prius Plug-in
    Model:
    Plug-in Base
    welcome!
    be sure to use toyota oem fluid
     
    #3 bisco, Dec 20, 2018
  4. JimboPalmer

    JimboPalmer Tsar of all the Rushers

    Joined:
    Apr 14, 2009
    12,470
    6,875
    2
    Location:
    Greenwood MS USA
    Vehicle:
    2012 Prius v wagon
    Model:
    Three
    The Gen 1 Prius (2001 - 2003) had a transaxle oil pan, none since.
     
    #4 JimboPalmer, Dec 20, 2018
  5. Stoner

    Stoner Junior Member

    Joined:
    Dec 19, 2018
    45
    20
    0
    Location:
    Naples, Florida
    Vehicle:
    2008 Prius
    Model:
    Two
    Thanks everyone for your replies!
    Stoner
     
    #5 Stoner, Dec 20, 2018
    Raytheeagle likes this.
  6. Patrick Wong

    Patrick Wong DIY Enthusiast

    Joined:
    Mar 8, 2008
    18,200
    6,490
    0
    Location:
    Green Valley, AZ
    Vehicle:
    2015 Prius
    Model:
    Two
    You will need a 24 mm 6 point socket and a 10 mm hex key socket. If you don’t have the first socket but instead have a 15/16” 6 point socket, that will work.
     
    #6 Patrick Wong, Dec 20, 2018
    Raytheeagle, jerrymildred and SFO like this.
  7. edthefox5

    edthefox5 Senior Member

    Joined:
    Jul 25, 2007
    10,096
    4,829
    0
    Location:
    Clearwater, Florida
    Vehicle:
    2007 Prius
    Model:
    Two
    Use name brand quality hex sockets not a pos harbor freight bit because those bolts are really really socked on there and if you strip the fill bolt side your screwed. Do the fill bolt first. The fill bolt is difficult as its hard to get leverage up in there. Use a breaker bar with a piece of emt pipe as an extension over the end of the breaker bar.

    I have dumped my trans fluid 3 times so far over 11 years. Based on what I see you really only need to do it once to get initial break in
    metal out. Its very kind to fluid after that. Worlds best transmission.I use pure synthetic Redline D6 fluid. Have for 11 years.
     
    #7 edthefox5, Dec 21, 2018
  8. jerrymildred

    jerrymildred Senior Member

    Joined:
    Oct 28, 2016
    11,517
    14,135
    0
    Location:
    Tampa, FL
    Vehicle:
    2017 Prius
    Model:
    Two
    #8 jerrymildred, Dec 21, 2018
    Prodigyplace likes this.
  9. Stoner

    Stoner Junior Member

    Joined:
    Dec 19, 2018
    45
    20
    0
    Location:
    Naples, Florida
    Vehicle:
    2008 Prius
    Model:
    Two
    #9 Stoner, Dec 22, 2018
    jerrymildred likes this.
(You must log in or sign up to post here.)