P0A80 wont go away after putting in a new battery

Discussion in 'Gen 3 Prius Care, Maintenance & Troubleshooting' started by pheanoukma, May 14, 2023.

  1. pheanoukma

    pheanoukma New Member

    Joined:
    May 14, 2023
    2
    0
    0
    Location:
    KH
    Vehicle:
    2010 Prius
    Model:
    Limited
    My car is a 2010 prius with the base option, it is showing signs of a dead traction battery so i use my laptop to scan the car and it shows 3 codes, 2 of the codes are weak cells and one of the code is the dreaded P0A80 so i basically bought a donor battery ( the donor is a 3rd gen prius ) then i swapped the whole battery assy into the car and the weak battery subcodes vanished, but the P0A80 stays and wont go away and it is stuck on permanent

    Also delta soc is 0
    and all the cells measured up to around 6-7 volts

    my only last choice is to take the 12v bat out and try it again
     
    #1 pheanoukma, May 14, 2023
  2. bisco

    bisco cookie crumbler

    Joined:
    May 11, 2005
    111,586
    50,814
    0
    Location:
    boston
    Vehicle:
    2012 Prius Plug-in
    Model:
    Plug-in Base
    is it starting?
     
    #2 bisco, May 15, 2023
  3. ASRDogman

    ASRDogman Senior Member

    Joined:
    May 29, 2018
    7,012
    3,669
    0
    Location:
    Florida
    Vehicle:
    2010 Prius
    Model:
    Two
    It's not your ONLY choice.
    Just disconnect the 12v battery for a minute, then reconnect it.
    Does the car start, and drive? If so, drive it. That code should go away after a while,
    at least I think that's one of the codes that need to read "X" amount of cycles withought
    a problem then it resets.

    Is the 12v battery in good shape?


     
    #3 ASRDogman, May 15, 2023
    pheanoukma likes this.
  4. TMR-JWAP

    TMR-JWAP Senior Member

    Joined:
    Aug 12, 2016
    6,404
    6,080
    0
    Location:
    Columbia, SC
    Vehicle:
    2007 Prius
    Model:
    Touring
    and all the cells measured up to around 6-7 volts

    If this is true, then your 'new' battery is dead as a door nail.

    I've replaced HV batteries in a few Gen 3s. Sometimes the P0A80 will NOT clear, even when trying to clear DTCs using techstream software. It's just one of those things. As long as the new HV battery is good, the 'Permanent' code will eventually clear itself after the proper number of drive cycles have been completed.
     
    #4 TMR-JWAP, May 15, 2023
    pheanoukma likes this.
  5. Mr. F

    Mr. F Active Member

    Joined:
    Sep 21, 2020
    386
    251
    0
    Location:
    Washington
    Vehicle:
    2010 Prius
    Model:
    IV
    The conditions that will clear up P0A80 with a healthy battery are mentioned here.
     
    #5 Mr. F, May 16, 2023
  6. pheanoukma

    pheanoukma New Member

    Joined:
    May 14, 2023
    2
    0
    0
    Location:
    KH
    Vehicle:
    2010 Prius
    Model:
    Limited
    it is man just changed it a while ago

    yup no lights on the dash and nothing, just the techstream software keeps telling me that theres a P0A80 code up in the battery

    upload_2023-5-17_16-22-38.png
    also this is the auxiliary bat voltage
     
    #6 pheanoukma, May 17, 2023
    Last edited by a moderator: May 17, 2023
  7. ASRDogman

    ASRDogman Senior Member

    Joined:
    May 29, 2018
    7,012
    3,669
    0
    Location:
    Florida
    Vehicle:
    2010 Prius
    Model:
    Two
    I'm glad it's running. That code should go away shortly.
    And that is NOT your battery voltage. That is the voltage the inverter is
    using to charge the battery.
    Check the battery with the car off. It should be above 12.6....

     
    #7 ASRDogman, May 17, 2023
    pheanoukma likes this.
(You must log in or sign up to post here.)