Search Results

Search Again
  1. EdwardFlorida
    Post

    2008 Brake and ABS light on and off

    Fluid level OK I will try to get codes. May go a several mile normal then come on. Stays on maybe 30 second then goes off again
    Post by: EdwardFlorida, Sep 6, 2020 in forum: Gen 2 Prius Care, Maintenance and Troubleshooting
  2. EdwardFlorida
    Post

    2008 Brake and ABS light on and off

    also if I pump the brake a couple of times the lights go off and brakes are normal again
    Post by: EdwardFlorida, Sep 2, 2020 in forum: Gen 2 Prius Care, Maintenance and Troubleshooting
  3. EdwardFlorida
    Thread

    2008 Brake and ABS light on and off

    2008 prius ABS and brake light come on and off. When off Brake function is normal, when on Brake performance poor as if no power assist.
    Thread by: EdwardFlorida, Sep 1, 2020, 4 replies, in forum: Gen 2 Prius Care, Maintenance and Troubleshooting
  4. EdwardFlorida
    Post

    Red Triangle

    Finally got it to go to ready by unplugging the hybrid battery plug on the drivers side and leaving out for 15 min. Now to go get a thorough...
    Post by: EdwardFlorida, Jul 21, 2020 in forum: Gen 2 Prius Technical Discussion
  5. EdwardFlorida
    Post

    Red Triangle

    Also when on the hybrid Battery indicator has 6 blue bars
    Post by: EdwardFlorida, Jul 20, 2020 in forum: Gen 2 Prius Technical Discussion
  6. EdwardFlorida
    Post

    Red Triangle

    Get 12. 1v at fuse panel
    Post by: EdwardFlorida, Jul 20, 2020 in forum: Gen 2 Prius Technical Discussion
  7. EdwardFlorida
    Post

    Red Triangle

    Dash is not black. All lights, brake Check engine Red Triangle etc. are on.Disconnected 12v for a while no change Replaced AM2 Fuse Not sure...
    Post by: EdwardFlorida, Jul 20, 2020 in forum: Gen 2 Prius Technical Discussion
  8. EdwardFlorida
    Post

    Red Triangle

    did bleed inverter
    Post by: EdwardFlorida, Jul 19, 2020 in forum: Gen 2 Prius Technical Discussion
  9. EdwardFlorida
    Post

    Red Triangle

    from Display monitor on dash 12v battery now says 11.6v
    Post by: EdwardFlorida, Jul 19, 2020 in forum: Gen 2 Prius Technical Discussion
  10. EdwardFlorida
    Post

    Red Triangle

    12.2 v on the 12v have not bled the inverter yet. Do not know on the OBD2 it is an Autel 309 Can you recommend a good hybrid compatible reader?
    Post by: EdwardFlorida, Jul 19, 2020 in forum: Gen 2 Prius Technical Discussion
  11. EdwardFlorida
    Thread

    Red Triangle

    Had inverter water pump go out again blows fuse dash goes black. Car dead in water. Replaced pump see flow in tank. Disconnected 12v neg. Still...
    Thread by: EdwardFlorida, Jul 18, 2020, 11 replies, in forum: Gen 2 Prius Technical Discussion
  12. EdwardFlorida
    Post

    Can't go into ready.

    Energy monitor problem solved 12v battery ground tightened.
    Post by: EdwardFlorida, May 13, 2019 in forum: Gen 2 Prius Care, Maintenance and Troubleshooting
  13. EdwardFlorida
    Post

    Can't go into ready.

    Did the first test here once codes were cleared. Went to IGN-ON and the triangle and other lights came up after about thirty seconds. It did...
    Post by: EdwardFlorida, May 8, 2019 in forum: Gen 2 Prius Care, Maintenance and Troubleshooting
  14. EdwardFlorida
    Post

    Can't go into ready.

    Had a hybrid specialty shop analyze. Got P0AA6 , C1259 and C1310. Tech checked cells and they were fine.
    Post by: EdwardFlorida, Apr 27, 2019 in forum: Gen 2 Prius Care, Maintenance and Troubleshooting
  15. EdwardFlorida
    Post

    Can't go into ready.

    Thanks tried to get them read at an import shop ( German, Asian) first thing they said was 12v was really discharging fast and needed to be...
    Post by: EdwardFlorida, Apr 26, 2019 in forum: Gen 2 Prius Care, Maintenance and Troubleshooting
  16. EdwardFlorida
    Thread

    Beep from console

    Have 2010 Prius. Runs perfect. When in ready mode there is a beep every 15 seconds coming from the console area. Occurs in any gear. No CEL or...
    Thread by: EdwardFlorida, Apr 25, 2019, 1 replies, in forum: Gen 3 Prius Care, Maintenance & Troubleshooting
  17. EdwardFlorida
    Post

    Can't go into ready.

    Then it is the "Master Warning light", "Brake system warning light" and the VSC " vehicle stability control system warning light". Hope that...
    Post by: EdwardFlorida, Apr 25, 2019 in forum: Gen 2 Prius Care, Maintenance and Troubleshooting
  18. EdwardFlorida
    Post

    Can't go into ready.

    only code is p1121 but it does not show up at first
    Post by: EdwardFlorida, Apr 23, 2019 in forum: Gen 2 Prius Care, Maintenance and Troubleshooting
  19. EdwardFlorida
    Thread

    Can't go into ready.

    2008 Prius 237k will not go into ready unless I disconnect the white rectangular plug on top of the battery. Once I do ready comes on and runs...
    Thread by: EdwardFlorida, Apr 23, 2019, 14 replies, in forum: Gen 2 Prius Care, Maintenance and Troubleshooting
Showing results 1 to 19 of 19
Search Again